top of page

Why We Keep Van Conversion Controls Out of the Cockpit

Oct 30
4 min read

There is something very tempting about a modern vehicle dashboard.

Screens. Menus. Buttons. The possibility of controlling almost everything without leaving the driver’s seat.

For people who design and manufacture commercial van conversions, the temptation is obvious: could we put the conversion controls there too?

We considered it. Mercedes-Benz offered to help us explore the integration process. The opportunity was there.

Then we asked a less glamorous question:

Where will our customers actually be when they need to use these controls?

Usually, in the workspace. With the vehicle parked.

That question shaped our decision.


The dashboard already has a job

Modern vehicles have sophisticated electronic systems. Integrating additional equipment into factory controls can involve manufacturer-specific interfaces, configuration, software work and diagnostic considerations. The requirements depend on the vehicle and the functions involved.

That does not make integration a bad idea. It means the benefit should justify the work.

At OIBD, we looked at what our clients needed from their mobile clinics, trade vehicles and mobile businesses. Their working day typically begins in earnest after they park.

A practitioner moves into the clinical area. A technician opens the equipment storage. A mobile business operator prepares the workspace.

The driver’s seat is no longer the centre of operations.

Putting workspace controls in the cockpit could look impressive. But would it make the customer’s job easier?


Our enthusiasm needed a practical question

People who build things can become very interested in what is technically possible.

We include ourselves in that statement.

Give us an interesting system and we will happily discuss its possibilities. The trick is remembering that the customer has a business to run while we are admiring the possibilities.

For this decision, our enthusiasm needed a simple test:

Would the operator be pleased to have this feature after the novelty wore off?

If someone is standing beside their equipment, walking back to the cockpit to adjust a workspace function may offer little practical advantage.

We chose to concentrate on accessible controls where the work happens.


Independent Van Conversion Controls, Coordinated Design

Our approach is to give the conversion its own appropriate controls rather than making factory cockpit integration the default.

Depending on the project, that can include controls and monitoring for lighting, onboard power, ventilation and installed equipment, positioned around the operator’s workflow.

Independent controls do not mean the conversion has no connection to the vehicle. Charging arrangements, mounting, electrical interfaces and any necessary vehicle signals still require careful assessment.

The distinction is about how the workspace is operated. We can design the conversion as a coordinated system without requiring its everyday functions to run through the factory dashboard.


Put the controls where the work happens

In a mobile clinic, the relevant question is what the practitioner needs to reach while preparing or using the clinical space.

In a trade vehicle, it is what the technician needs when accessing tools, equipment or a work surface.

In a mobile business, it is how the operator prepares the vehicle for service and manages the working day.

These are different environments. Control locations should follow those differences.

A good layout considers access, visibility, operating sequence and the equipment involved. Some functions may also need interlocks or restrictions appropriate to their use.

The aim is straightforward: help people operate the workspace without unnecessary steps.


Think about the day something needs attention

Design decisions also matter after handover.

When equipment needs attention, a clearly documented division between factory vehicle systems and conversion systems can help technicians identify where to begin investigating.

It does not eliminate faults or guarantee a quick diagnosis. It does help establish which equipment, wiring and controls belong to each part of the build.

That is why we value accessible components, circuit identification, system documentation and component traceability alongside the finished appearance.

A tidy control panel is useful. Knowing what sits behind it is useful for considerably longer.


When cockpit integration earns its place

There are applications where cockpit integration makes sense.

If a function genuinely needs to be available to the driver, or a specialist operational requirement depends on a vehicle interface, it deserves proper investigation with the relevant manufacturer and technical specialists.

Our decision is therefore made project by project.

We ask what the function achieves, who operates it, when they need it and what integration requires.

For many of our commercial conversions, independently operated workspace controls provide the practical arrangement we are looking for. Other applications may justify a different solution.


The lesson: let the working day guide the design

We did not arrive at this approach after a dashboard full of warning lights or an integration disaster.

We explored the opportunity, listened to what was involved and considered the benefit to the customer before committing to it.

Sometimes the useful design lesson is recognising complexity before you build it into the project.

Our clients need vehicles that help them deliver a service, reach their equipment and get through a working day. That gives us a clear starting point for decisions about controls, storage, power and layout.

The dashboard can keep doing its job.

We will put the workspace controls where they earn their place.


Planning a commercial van conversion?

Oz Interior by Design designs and manufactures commercial van fitouts, mobile specialist clinics and mobile business vehicles at our Smithfield workshop in Sydney.

As a Mercedes-Benz VanPartner operating an ISO 9001-certified quality management system, we approach each project around the vehicle, installed equipment and intended use.

Explore our commercial van fitout solutions, or contact our team on 1300 470 343 to discuss your project.


By Durham Zumot, Managing Director and Co-Founder, Oz Interior by Design.


Concept illustration showing a Mercedes-Benz van cockpit beside independent touchscreen and switch controls in a commercial workspace.

Driving controls in the cockpit. Workspace controls where the work happens. Concept illustration.

 
 
 

Comments


bottom of page